Vehicles
54 not categorized PORSCHE 996 HOSE KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.96411602853 Higher transmittable torque. Higher clamping load. Less abrasion. Direct replacement for the oe pressure plate. 240 mm. Max torque: 486 lb/ft (660 nm) weighs: 9.5 lbs. (4.3 kg) the reinforced sachs performance pressure plate (clutch cover) has fundamental advantages against an oe pressure plate, such as a higher transmittable torque and higher resistance against thrust. It also allows for faster and sportier gearshifts. That makes it extremely useful for street tuning, endurance races and hill climbing. The sachs performance clutches are assembled by hand. This guarantees the highest quality attributes in clamping load and release characteristics. Installation notes for those with single mass flywheel kits: whe...(choose a part on the right to read more) View/Change Diagram
From $634.70
Make a selection 9217 The ultimate in cooling efficiency. The stacked-plate design offers maximum cooling with almost bulletproof strength. Aircraft quality aluminum, flux-less oven brazed construction. Cross-path airflow effectively cools oil as air passes through as many as 16 paths across sturdy embossed plates. Insignificant pressure drop, twice the cooling in half the size! Painted black for fast heat dissipation. Complete kits includes cooler, sandwich adapter with 3/4" x 16 nipple, remote filter bracket, high temperature hose and all fittings required for installation on your 914 or 912e. The sandwich adapter fits between stock oil filter mount and oil filter. General Fitment912 1965-69914 1970-76
$217.71
Make a selection 95037504 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment911 1989-94
$63.42
Make a selection AFC11958 A necessary addition for any 911! This kit includes the components needed to install a mocal 44 row 115 matrix oil cooler in cars with factory "hard line" plumbing. This kit is perfect for upgrading existing factory coolers to the more efficient mocal oil radiator. Includes the cooler, two metric x am adaptor, two straight -12am fittings, one 45 degree -12am fitting, one 90 degree -12am fitting, and two -12am stainless streel hoses. This is the biggest oil cooler kit we offer for the fender of a 911. Note: for car that already have a factory oil cooler. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$549.95
Make a selection AA007 Developed at Automobile Atlanta, and featured in vw Porsche magazine, this fuel pump relocation kit solves vapor lock! factory authorized and tested in hundreds of 914's, this kit moves the fuel pump close to the 1975-76 location. Everything you need plus precise installation instructions are included. General Fitment914 1970-76
$70.04
Make a selection AAVACKIT2 Our vacuum line kits solve the lean running, poor performance, and high/low idle caused by vacuum leaks! Custom cut, colorful, and easy to install, new vacuum lines also dress up your engine compartment! Kit comes complete with vacuum cartoon for easy installation. kit does not include the large 19 mm hose. General Fitment914 1970-76
$89.99
Make a selection AAVACKIT5 Our vacuum line kits solve the lean running, poor performance, and high/low idle caused by vacuum leaks! Custom cut and easy to install, new vacuum lines also dress up your engine compartment! Kit comes complete with vacuum cartoon for easy installation. kit does not include the rare 20mm hose from the oil filler to the air cleaner. Picture is representative only. General Fitment914 1970-76
$89.50
Make a selection AFC11957 A necessary addition for any 911! This kit includes substitute 30% larger 310 matrix (14"h x 6"w x 2"d) 19 row oil cooler in a factory "hard line" equipped car. This kit is especially good for replacing the factory "loop" oil device located in the front right fender, making it easy to upgrade to a mocal oil radiator at an economical price. Includes the cooler, two 90 degree 3/4 fittings, two 30 mm straight fittings, and a 3/4 oil hose. this is larger than out basic oil cooler kit. Note: for car that already have a factory oil cooler. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$475.00
Make a selection AP970TT103 With the insane results of our aluminum y-pipe kit for the Porsche panamera turbo, we wanted to step up the luxury look of the engine bay with a full carbon fiber version. this carbon fiber y-pipe is a full replacement and includes everything you need to install in place of the original. General FitmentPANAMERA 2010-14
$1,849.95
Make a selection BES98725001SBE - + 15 crank hp & + 14 crank torque. General FitmentBOXSTER 2009-11
$4,351.75
Make a selection BAT001 The mocal oil cooling kit for the Porsche 914-4 consists of a 25 row -10an oil cooler & 7/12" cooling fan with with a sp1t thermostatic sandwich plate and -10an aqp stainless hose and fittings. The cooler is mounted to the underside of the engine grille, the plastic rain pan can be removed or a hole the size of the cooler can be made in the center. The sp1t thermo. Sandwich plate mounts between the oil filter and the filter mount allowing oil flow to the cooler after 180 degrees. We supply enough aqp stainless oil hose and aircraft fittings to link the sandwich plate to the oil cooler. General Fitment914 1970-76
$570.00
Make a selection BAT006 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30mm metric to -12 an adaptors for the oil ta...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73
$1,179.45
Make a selection BAT005 Many pre. 1977 Porsche 911's are not equipped with factory oil plumbing (hard lines and thermostat). In this case fitting an oil cooler requires making a hose run from the rear to the front of the vehicle and back. We find the easiest and most cost effective method of plumbing is to duplicate the factory plumbing route using aeroquip hose and fittings with a mocal oil thermostat and oil cooler. The various kits that we offer to accomplish this task include; one of a number of oil cooler options (some are suitable for both fender or front spoiler location), mocal -12 an oil thermostat with mounting bracket, 30 foot length of aqp -12 an stainless braid 3/4" id hose, 30 mm metric to -12 an adaptors for the oil t...(choose a part on the right to read more) General Fitment911 1974-77911 1965-69 911 1970-73 928 1978-82
$1,090.00
Make a selection BES91110000S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche® owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. To further ensure quality, all of our exhaust systems meet the standards of the German independent testing agency tÜv; whose quality standards are among some of the strictest in the world. General Fitment911 1970-73
$5,357.49
Make a selection BES91100100S Brombacher exhausts are engineered for the discerning Porsche® owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. To further ensure quality, all of our exhaust systems meet the standards of the German independent testing agency TUV; whose quality standards are among some of the strictest in the world. General Fitment911 1978-83930 1975-77 911 1974-77 911 1984-86 911 1987-89
$6,891.50
Make a selection BES96410100S FVD "brombacher" sound version exhaust system for 964 89-94 General Fitment911 1989-94
$8,518.40
Make a selection BES99605001S Our street version muffler set is perfect for those more concerned with a quality Porsche flat 6 sound rather than just an increase in decibels. This is the perfect addition for a cabriolet, for those concerned about drone, or for those interested in a quality flat 6 exhaust note without drawing to much attention. These are also ideal for anyone planning or running sport cats or bypass as they will offer more dampening so that extreme decibels are not experienced. These mufflers also pass the strict decibel limits set by the German TUV and they include TUV certification. Features: - + 8 crank hp & + 8 crank torque - weighs 35.7 lbs. (16.2 kg) - German v2a - x5crni18-10 - 1.4301 (t304) stainless steel for improv...(choose a part on the right to read more) General Fitment911 1998-05
From $1,807.30
Make a selection 996TTHFPPPB The automotive speed technologies 996 tt fresh air intake plenum and hard inlet pipe kit is designed to enhance the performance of your Porsche 996 tt by allowing fresh air to flow freely to the turbos for quick spool and additional power - very important for modified cars running larger than OEM turbos or running high boost. The system consists of the speedtech hi-flow intake plenum with 70mm outlet tubes, attached to 70mm molded hard plastic tubes for uniform high flow. Silicon hose is supplied to connect to the turbo inlets. The speedtech hi-flow plenum is designed to flow more air than the OEM plenum and deliver it quickly and smoothly with no restrictions from the maf tube all the way to the turbo inlets. ...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2001-05
$2,551.50
Make a selection BES99709060S1 Brombacher racing exhaust system for 997gt3/rs General Fitment911 GT3 2007-11
From $3,177.67
Make a selection BES99709260S90 Brombacher racing exhaust system for 997gt3/rs with 90mm x 2 round tips General Fitment911 GT3 2007-11
From $6,698.73
Make a selection BES99710260S - + 25 crank hp & + 27 crank torque General Fitment911 GT3 2007-11
$8,549.20
Make a selection BES99709260SRS Brombacher racing exhaust system for 997gt3/rs General Fitment911 GT3 2007-11
$6,996.00
Make a selection BES99710200S8 Facts: General Fitment911 2005-08
$8,826.40
Make a selection BES99710260T - + 25 crank hp & + 25 crank torque General Fitment911 GT3 2007-11
$20,056.30
Make a selection BES99720200SHD "brombacher" stainless steel exhaust system for the 997-2 General Fitment911 2009-12
From $7,994.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |